ball joint noise

Shock and Strut Diagnosis The shock absorber/strut is the most commonly replaced component in the suspension system. The shock absorber wears out slowly over time so it is difficult to establish exactly when the shock/strut needs to be replaced. Worn Shock Safety Concerns Besides ride quality a worn out or failed shock/strut can cause: Reduced steerability – especially on rough roads increased braking distance Shock/Strut Noise Worn shock bushings and attachment hardware will produce a rattling noise when the vehicle is driven over uneven surfaces. Other suspension components can cause a similar noise so a visual inspection is needed to identify the faulty part. Visual Inspection of Shock/Strut Fluid leaking from the area around the seal indicates the seal has failed and immediate replacement is necessary. A very small amount of fluid ‘mist’ around the seal is normal, but liquid coating the upper part of the shock is a definite sign of seal failure.Check for worn or broken rubber bushings. Worn or Damaged Jounce Stops Split, cracked, or damaged jounce stops are a sign of worn shocks and or springs. Damaged Dust Bellows Since the jounce stop is often integrated with the dust bellows a damaged, broken or torn dust bellows is a sign that the strut has lost dampening ability. Shock Diagnosis After a visual inspection of the shocks and suspension, a road test is needed to assess the dampening ability of the shock. Symptoms of worn shocks:Excess pitch and roll oscillations after encountering bumps in the road.Excessive dive during braking or squat during acceleration. In general, worn shocks produce a mushy ride and wallowing. Strut Mounts Symptoms of worn or damaged strut mounts: - Rattling noise on uneven surfaces - Clunk noise when the vehicle is steered left and right - Notchy steering or frozen steering - Pull to either side A worn or incorrectly installed strut mount will effect the wheel alignment Checking Strut Mounts Lateral Freeplay With the vehicle raised so that the tire is about 1 inch off the floor pry the tire upward to take some of the load off the mount.Pry the center of the mount side to side to measure lateral Freeplay.Pry the whole strut up and down to measure axial Freeplay. Ball joint Lubrication Most modern passenger cars are built with sealed ball joints and tie rod ends that are greased for life and require no maintenance.Aftermarket replacement ball joints often have grease fittings that allow grease to be injected into the joint under high pressure. Chassis Lubrication Heavy trucks normally have grease-able joints on all the suspension and driveline components.Most automotive applications will use a general-purpose GL-1 or GL-2 to grease all of the suspension components with grease fittings. NLGI grade number Chassis grease standards are set by the National Lubricating Grease InstituteThere a 9 grades ranging from 000 to 6The higher the number the thicker the greaseGrease that is too thin will leak out of the jointToo thick and the grease cannot work its way in-between the ball and seatGL-1 and GL2 are the types of grease normally used in suspension and steering jointsGL-2 has the consistency of peanut butter Zerk Fitting The only way to grease a ball joint is through a Zerk fitting.The Zerk fitting couples the grease gun to the joint.A spring-loaded ball in the center of the fitting prevents grease from leaking out.The Zerk fitting is screwed into the ball joint and can be easily replaced. Grease Guns Most hand-operated grease guns can produce 6000 psi or more.Shops that work mostly on passenger cars will normally use hand-operated grease guns as there are very few applications on modern cars that require periodic greasing.Shops that work mostly on trucks will have pneumatically operated grease guns that save time when a vehicle has several dozen grease fittings. Ball joint Boots Most modern passenger cars have sealed boots that a clamped tight to the ball joint with spring steel clips.When greasing this type of joint you only pump one or two strokes of grease into the joint – until the boot swells slightly.Older cars and trucks may have loose-fitting ‘umbrella’ type boots that allow a small amount of grease to leak out of the skirt.Fill these ball joints until grease flows out of the boot skirt. Ball Joints – Visual Inspection A ball joint should last indefinitely if the rubber boot that retains the grease and keeps dirt and moisture out remains intact. Any visible damage to the rubber boot is reason enough to replace the ball joint. Grease-able ball joints will often have excess grease on the boot and control arm. Checking ball joints For Wear If the spring is positioned on the lower control arm the upper and lower ball joints are under tension when the wheels are off the ground.Place a jack stand under the lower control arm as far outboard as possible.After lowering the vehicle onto the jack stand if there is a gap between the rebound stop and the upper control arm the ball joints are now unloaded.If the spring is positioned on the upper arm the ball joints will be unloaded then the wheels are off the ground.The rebound stop will be in firm contact with the upper arm. Measuring ball joint Freeplay Freeplay measurements are made between the steering knuckle and ball joint/control arm in both axial and lateral directions.Specifications for ball joint Freeplay can be found in AllData. Replacing ball joints Ball joints are Retained in the Control Arms by: Press-fit ThreadedRivetsBoltsIntegrated into the control arm Press Fit and threaded ball joint A special 8 point ball joint socket is needed to remove and install this type of ball joint Ball joint Retained by Rivets Replacing this type of joint requires that the rivets be drilled out.The new ball joint is retained with bolts and nylock nuts.Alternatively, the heads of the rivets can be ground off using a die grinder.Never cut the rivet heads off with an oxy-acetylene torch. Integral and bolted ball joints Ball joints that are retained by bolts are commonly found on vehicles with MacPherson struts.Integral ball joints are bolded directly o the control arm.The entire control arm is replaced when the ball joint is worn out. Separating the ball stud The ball stud is slightly tapered.After the retaining nut has been removed several tons of force will be needed to separate the ball stud from the steering knuckle. Hammer Method This technique can only be used on forged steel steering knuckles.Strike the steering knuckle on the area surrounding the ball joint tapered stud with the flat side of a 5 lbs, ball-peen hammer.Never strike the threaded part of the stud with a hammer. Pickle fork method Like the hammer method, this technique should only be used on forged steel steering knuckles.This technique will destroy the ball joint’s rubber boot so it is only used when replacing ball joints.A similar forked tool can be used with a pneumatic hammer. Screw type ball joint separator The screw-type separator does not damage the rubber boot or ball stud threads.A steel disc positioned between the ball stud and the pushing screw distributes the force on the stud evenly.Many technicians back of the retaining nut 3 or 4 turn but leave it on the ball stud to protect the threads of the stud.They are a number of screw-type ball joint separators available to fit most applications. Pinch bolt retained ball joints Pinch bolts are often used to retain the ball joint stud to the steering knuckle.A slot is cut through the steering knuckle into the ball stud hole.A pinch bolt squeezes the steering knuckle tight to the ball stud,The pinch bolt passes through a groove in the ball stud – ensuring that the ball joint stays attached to the knuckle even if the bolt loosens. Ball joint press A ‘C’ clamp-type press is used to press the old ball joint out and press the new joint in while the control arm is still attached to the frame. Pressing out ball joints Press fit ball joints can be serviced on the car with a C-clamp type press or off-the-car using a hydraulic shop press.A receiver sleeve is needed to support the control arm.The receiver must be large enough to accept the large end of the ball joint. Ball joint press The receiver sleeve is often notched to allow clearance where sections of the control arm are very close to the ball joint bore.A ram sleeve is needed to apply even pressure to the smaller end of the ball joint. Ball joint press - removal The inner diameter of the receiver must be slightly larger than the outer diameter of the ball joint.The ram needs to be slightly smaller than the ball joint bore in the control arm.The press screw should be turned by hand.Using an impact wrench damages the screw threads. Ball joint press - installation For installation, we need to select a ram sleeve that fits the outer body of the ball joint.The receiver sleeve must be long enough to accept the full length of the ball stud.The inside diameter of the receiver must be slightly larger than the small end of the ball joint. Castellated nut and cotter pin The correct way to install the cotter pin on a castellated nut is shown on the left.The excess on the lower side of the cotter pin is cut off with diagonal pliers before bending. Ball joint R&R If the ball joint is being replaced a hammer and pickle fork can be used. Use a jack stand for safe removal A jack stand is placed under the lower control arm to prevent possible injury when the steering knuckle is separated from the ball joint. Setting up the press Pressing out the ball joint Do not use an impact wrench with any type of screw press. Using an impact wrench damages the threadsA ½” ratchet with an 18” handle is the ideal tool for the job. Control arm after removal The hole in the control arm should be cleaned with sandpaper and lubricated before installing the new ball joint. Installing the new ball joint Insert the new ball joint in the control arm and place the receiver sleeve and adapter on top. Install the pressing adapter The adapter used to press the ball joint into the control arm needs to be sized to apply pressure to only the outer circumference of the ball joint. Pressing in the new ball joint Make sure the ball joint is aligned and straight as you press it into the control arm. Check for gaps Check to make sure there isn't any gap between the step on the ball joint and the control arm flange. Correctly installed ball joint Boot Orientation The boot for this vehicle is not symmetrical so it must be positioned with the arrow pointing inward. Install the boot If the boot needs to be stretched to fit over the ball joint use care so the boot is not damaged. Install Zerk fitting The Zerk fitting threads into the bottom of the ball joint Riveted type ball joint The upper ball joint on this vehicle uses a riveted type joint. The rivets will be drilled out and replaced with bolts and locking nuts during the replacement process. READ MORE https://youtu.be/E9O_cOB2MTI https://youtu.be/62bVn7E8gyk https://youtu.be/ZztbAShnlxw https://youtu.be/37NgLM4tIzw READ MORE: A QUICK GUIDE TO DIAGNOSING 10 COMMON STEERING ISSUES5 WARNING SIGNS OF BAD INTERMEDIATE STEERING SHAFTS3 COMMON SYMPTOMS OF LOW POWER STEERING FLUIDELECTRIC VS HYDRAULIC POWER STEERINGHOW POWER STEERING WORKS?STEERING SYSTEM: REQUIREMENTS, TYPES, POWER STEER Visit Forum Visit Our Friendly Website

Tag: ball joint noise

Suspension Service: Shock Absorbers and Ball Joints

Everything You Need to Know About Ball Joints | Ultimate Guide